ESSENTIAL PLUMBING INSIGHTS FOR INSTALLING A BATHTUB

Essential Plumbing Insights for Installing a Bathtub

Essential Plumbing Insights for Installing a Bathtub

Blog Article

Call

Each person has their own conception when it comes to How to Install a Bathtub.


Tools You Need to Install a New Bathtub
Setting up a bathtub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and also often, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult task. If the old bathtub is easily obtainable, the job can relocate easily; if you have to open up a wall surface to remove the old tub as well as place the brand-new tub, the job is a lot harder. In either instance, the task is within a house handyman's abilities, although you will certainly need an assistant to move out the old tub and also embeded in the new one. See to it you have actually qualified yourself for the job and also fit attempting it. As opposed to employing a service provider to take control of a halfway-completed job, it is much better to think about employing one prior to you begin. Possibilities are you may need a specialist plumber to make tube connections.
This write-up will certainly help you install a brand-new tub in your washroom if you have actually currently acquired a brand-new bathtub and don't require to transform the setup of your previous water supply pipelines.
Your devices as well as material checklist ought to consist of the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Getting ready for the Setup


    Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to prevent pressure on the bathtub.
    Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use every one of the supplied washing machines.
    Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its last setting.

    Removing Old Taps


    If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be quite troublesome due to the restricted accessibility that is often the situation.
    Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have been eliminated, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any old securing substance.
    Before moving on to fit the brand-new taps, compare the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.

    Setting up the Bathtub


    Making use of both wooden boards under its feet, position the tub in the required position. The wooden boards are useful in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little points.
    The following goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bath tub till the spirit level reviews degree.
    To install taps, fit all-time low of the outermost adaptable tap port to the proper supply pipe by making a compression join; then do the same for the other faucet.
    Turn on the water supply and also check all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill the bath tub and likewise check the overflow outlet and the regular outlet for leaks.
    Lastly, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bath tub needs to wait till the tub has actually been utilized at least when as this will settle it right into its last position.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the current supply pipes.
    If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next, place the tap in the mounting opening in the bath/basin making sure that the washers are in area between the faucet and the sink. Safeguard the faucet in place with the producer supplied backnut. Once the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous kind should be connected to the tap finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bathtub


    In the location where the bathroom fulfills the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, causing issues with wetness and also possible leaks to the ceiling below.
    You can choose from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes as well as cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealant can fracture fairly very early if you do not take into consideration this movement prior to securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily available on the market. It is suggested to fit the floor tiles making use of water-resistant or waterproof glue and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    We are very intrigued by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you appreciated the new blog post. Don't hesitate to take a moment to promote this blog posting if you enjoyed it. Thanks a lot for your time. Visit us again soon.


    Address leaks promptly.

    Report this page